<font id="ftddx"></font>
<dl id="ftddx"><output id="ftddx"><font id="ftddx"></font></output></dl>
<dl id="ftddx"><output id="ftddx"></output></dl>
<video id="ftddx"></video>
<dl id="ftddx"></dl>
<video id="ftddx"><output id="ftddx"></output></video>
<dl id="ftddx"></dl><noframes id="ftddx"><video id="ftddx"></video><video id="ftddx"></video><video id="ftddx"><output id="ftddx"><delect id="ftddx"></delect></output></video><output id="ftddx"></output>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"><font id="ftddx"></font></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
<noframes id="ftddx">
<dl id="ftddx"><output id="ftddx"><font id="ftddx"></font></output></dl>
<video id="ftddx"><output id="ftddx"></output></video>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"><delect id="ftddx"></delect></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"><delect id="ftddx"></delect></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"><output id="ftddx"><meter id="ftddx"></meter></output></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
當前位置:新聞資訊 > 行業新聞

旋切機的木皮厚度控制

發布日期:2017-09-09 18:37:32 訪問次數:2079

   旋切機在出廠前都是按照1-2毫米的厚度設置的。如果后期想要改變木皮的厚度,首先就要調整旋切機的壓力。用三角尺(500*250mm)靠住旋切機雙花滾的上部和內側,用150毫米的直尺頂住單花滾的上面觀察三角尺下邊與直尺交接處的數值,皮子厚1-2毫米時取35mm-36mm,如皮子厚度規格小于1毫米以下時讀數值相應加大,如皮子厚度規格大于2.0毫米以上時,讀數值相應減小。如果要增加旋切機的壓力時,要向兩側單箱和刀臺肩之間分別增加墊片;壓力減小時,減少墊片即可。

上一信息:暫無

下一信息:旋切一體機的使用技巧如何減少換刀率?

日韩精品无码区免费专区
<font id="ftddx"></font>
<dl id="ftddx"><output id="ftddx"><font id="ftddx"></font></output></dl>
<dl id="ftddx"><output id="ftddx"></output></dl>
<video id="ftddx"></video>
<dl id="ftddx"></dl>
<video id="ftddx"><output id="ftddx"></output></video>
<dl id="ftddx"></dl><noframes id="ftddx"><video id="ftddx"></video><video id="ftddx"></video><video id="ftddx"><output id="ftddx"><delect id="ftddx"></delect></output></video><output id="ftddx"></output>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"><font id="ftddx"></font></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
<noframes id="ftddx">
<dl id="ftddx"><output id="ftddx"><font id="ftddx"></font></output></dl>
<video id="ftddx"><output id="ftddx"></output></video>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"><delect id="ftddx"></delect></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"><delect id="ftddx"></delect></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"><output id="ftddx"><meter id="ftddx"></meter></output></dl>
<dl id="ftddx"></dl>
<dl id="ftddx"></dl>